Fusion Crysta Adhesive Primer

  1. Home
  2. Orthodontics
  3. Fusion Crysta Adhesive Primer

Fusion Crysta Adhesive Primer

Light Cure Self Etch Orthodontic Primer
  • 10-MDP based light cure, single component primer
  • Combines etching, priming & bonding in a single composition
  • No Post operative sensitivity
  • High bond strength & durability

PACKAGING

  • Regular Pack : 1 x 5ml Bottle, 5 x Mixing Wells, 10 x Micro Brushes
    1 x Instruction Manual.

900.00

Quantity

CE 0123
The product is audited & approved as per European standards and laws, and has a valid CE Certifications
MDSAP
MDSAP quality management system satisfies the regulatory jurisdictions requirements of MDSAP Countries
CDSCO Registered
CDSCO
Registered & Approved as per MDR 2017 Guidelines by Central Drugs Standard Control Organization
Orthodontic Adhesive primer
Orthodontic Adhesive primer
Orthodontic Adhesive primer

INDICATIONS

  • Used for adhesion of orthodontic brackets when used along with an adhesive

PRODUCT BENEFITS

  • Single bottle with etch, prime & bond provide clinically acceptable bond
    strength
  • The primer contains the revolutionary 10-MDP
  • (10-MDP) a functional monomer which helps in bonding to dentin, cut
    and un-cut enamel.
  • MDP promotes physical and chemical adhesion
  • No post operative sensitivity
  • High bond strength and durability
Technical Data Standard Applied
1. Bond Strength 20 MPa ISO 29022

Reviews

There are no reviews yet.

Be the first to review “Fusion Crysta Adhesive Primer”

Your email address will not be published. Required fields are marked *

Instruction for use :

SELF-ETCHING TECHNIQUE : Wash thoroughly with water spray. Use an absorbent pellet or high volume evacuation (HVE) for 1-2 seconds, to remove excess water (do not dessicate).

  1. Dispense 1-2 drops of Fusion Crysta Adhesive Primer into a clean well. Replace the cap onto the bottle promptly to avoid evaporation of solvent.
  2. Apply two separate coats of Fusion Crysta Adhesive Primer, scrubbing the preparation with a microbrush for 10-15 seconds per coat.
  3. Air-drying using an air syringe for at least 10 seconds till there should be no visible movement of the adhesive. The surface should have a uniform glossy appearance; otherwise, apply an additional coat of FUSION CRYSTA ADHESIVE PRIMER and repeat Step 2 and 3.
  4. Light cure for 20 seconds.
  5. Continue with placement of the orthodontic adhesive (FUSION CRYSTA ADHESIVE) restorative material according to the manufacturer’s instructions.

SELECTIVE-ETCHING TECHNIQUE : Wash thoroughly with water spray. Etch enamel using 37% phosphoric acid (ACTINO GEL) etchant for 15 seconds. Rinse thoroughly. Remove excess water by blotting the surface with an absorbent pellet or high volume evacuation (HVE) for 1-2 seconds, leaving the preparation visibly moist.

  1. Dispense 1-2 drops of Fusion Crysta Adhesive Primer into a clean well. Replace the cap onto the bottle promptly to avoid evaporation of solvent.
  2. Apply two separate coats of Fusion Crysta Adhesive Primer, scrubbing the preparation with a microbrush for 10-15 seconds per coat.
  3. Evaporate excess solvent by thoroughly air-drying with an air syringe for at least 10 seconds, there should be no visible movement of the adhesive. The surface should have a uniform glossy appearance; otherwise, apply an additional coat of FUSION CRYSTA ADHESIVE PRIMER and repeat Step 2 and 3.
  4. Light cure for 20 seconds.
  5. Continue with placement of the orthodontic adhesive (FUSION CRYSTA ADHESIVE) restorative material according to the manufacturer’s instructions.

Storage conditions : Store at temperature between 10°C to 24°C. Close the cap carefully after use. Keep away from moisture. Shelf life not affected after opening if stores in a cool dry place.

Shelf Life : 2-years from the date of manufacturing.

Quick Cart

Add a product in cart to see here!
0