Fusion Crysta Orthodontic Adhesive Kit

  1. Home
  2. Orthodontics
  3. Fusion Crysta Orthodontic Adhesive Kit

Fusion Crysta Orthodontic Adhesive Kit

Light Cure Orthodontic Adhesive Kit
  • Light Cure Composite kit for Orthodontic Purpose
  • Used for bonding of Metal & Ceramic Brackets to tooth surface
  • Cementation of Molar Bands

PACKAGING

  • REGULAR Orthodontic Kit : 1 x 4g Syringe, Fusion Crysta Adhesive, 1 x 5ml Bottle, Fusion Bond 5, 1 x 5ml Syringe, Actino Gel, 10 x Applicator Tips, 1 x Instruction Manual

1,800.00

Quantity

CE 0123
The product is audited & approved as per European standards and laws, and has a valid CE Certifications
MDSAP
MDSAP quality management system satisfies the regulatory jurisdictions requirements of MDSAP Countries
CDSCO Registered
CDSCO
Registered & Approved as per MDR 2017 Guidelines by Central Drugs Standard Control Organization
Orthodontic Adhesive Kit
Orthodontic Adhesive Kit
orthodontic adhesive kit

INDICATIONS

  • Used for Bonding Metal & Ceramic brackets to tooth surface and for cementation of molar bands.

PRODUCT BENEFITS

  • Highly translucent adhesive designed to compliment traditional and LED curing lights
  • Superior physical properties
  • The primer contains the revolutionary 10-MDP
  • MDP promotes physical and chemical adhesion
  • High enamel bond strengths
  • Excellent handling properties
Technical Data Standard Applied
1. Flexural Strength 60 – 90 MPa ISO 4049, 29022

Reviews

There are no reviews yet.

Be the first to review “Fusion Crysta Orthodontic Adhesive Kit”

Your email address will not be published. Required fields are marked *

Instructions for Use :

Tooth Preparation : Rinse, isolate, and thoroughly air-dry (clean, oil-and-water-free compressed air) the surface area to be bonded.

Acid Etching : Etch enamel using 37% phosphoric acid (ACTINO GEL) etchant for 15 seconds. Rinse thoroughly. Remove excess water by blotting the surface with an absorbent pellet or high volume evacuation (HVE) for 1-2 seconds, leaving the preparation visibly moist.

Priming teeth :

  1. Dispense 1-2 drops of FUSION CRYSTA ADHESIVE PRIMER into a clean well. Replace the cap onto the bottle promptly to avoid evaporation of solvent.
  2. Apply two separate coats of FUSION CRYSTA ADHESIVE PRIMER, scrubbing the preparation with a micro brush for 10-15 seconds per coat.
  3. Air-drying using an air syringe for at least 10 seconds till there should be no visible movement of the adhesive. The surface should have a uniform glossy appearance; otherwise, apply an additional coat of FUSION CRYSTA ADHESIVE PRIMER.
  4. Light cure for 20 seconds.

Adhesive application from syringe and light curing : With the syringe apply a small amount of adhesive paste onto bracket base. Immediately after applying adhesive, lightly place bracket onto the tooth surface. Adjust bracket to final position, press firmly to seat bracket. A small amount of excess adhesive around appliance base should exude without disturbing the bracket. Final adjustment must be made before the adhesive begins to cure. Using a conventional halogen curing light or a LED light, polymerize entire bonded surface for 20 seconds from the facial, mesial, and distal directions. The dispensed material shall not be placed back in container and the dose once applied and used shall not be reused.

Warnings : Avoid prolonged or repeated contact with skin (allergic contact dermatitis), and eyes. Avoid prolonged inhalation. Do not take internally. Contact with the skin may cause irritation and hypersensitivity. If contact with skin occurs immediately wipe off thoroughly with cotton and alcohol and then wash well with soap and water. If skin rash and sensitization or other allergic reaction occurs discontinue use and seek medical attention. If the product comes into contact with the eyes, rinse thoroughly with fresh water and consult a physician.

Precautions : Eugenol containing materials should not be used with this product because they may effect polymerization and interfere with the hardening process. Being sensitive to heat and light, the syringes should be kept away from direct sun light.

Contraindications : It is contraindicated for use with patients who have a history of severe allergic reaction to methacrylate resins.

Storage Conditions : Store at temperature between 10°C(50°F) to 24°C(75°F). Close the cap carefully after use. Keep away from moisture. Shelf life not affected after opening if stored in a cool dry place.

Shelf Life : 3 years from the date of manufacturing.

Quick Cart

Add a product in cart to see here!
0