Crysta Luting

  1. Home
  2. Cements & Liners
  3. Crysta Luting

Crysta Luting

Translucent Fine Particle Glass Ionomer Luting Cement
  • A type 1 GIC cement for luting of crowns, bridges, inlays, onlays, post & orthodontic brackets
  • A self-cure, fine particle formula with fluoride releasing properties


  • Powder – Liquid Kit : 1 x 15g Powder Jar, 1 x 10ml Liquid Bottle, 1 x Mixing Pad, 1 x Spoon, 1 x Instruction Manual.



CE approved
CE 0123
The product is audited & approved as per European standards and laws, and has a valid CE Certifications
MDSAP quality management system satisfies the regulatory jurisdictions requirements of MDSAP Countries.
CDSCO Registered
Registered & Approved as per MDR 2017 Guidelines by Central Drugs Standard Control Organization
type 2 luting glass ionomer cement
type 2 luting glass ionomer cement


  • Cementation of inlays, onlays and crowns
  • Cementation of posts and screws
  • Attachment of metal orthodontic bands


  • High fluoride release
  • Low solubility
  • Translucent shade
  • Very low film thickness
Technical Data Standard Applied
1. Ratio (Powder / Liquid) 1 : 2 ISO 9917-1
2. Mixing Time 45 – 60 Sec.
3. Setting Time 2 Min 30 Sec.
4. Compressive Strength 108.43 MPa
5. Film Thickness 20 μm


There are no reviews yet.

Be the first to review “Crysta Luting”

Your email address will not be published. Required fields are marked *

Instructions for Use :

Powder/Liquid ratio (0.19/0.12), Mixing time (min. sec) : 45-60 seconds, setting time (min. sec) : 2min 30sec, (at 23±1°C from start of mixing) Final finishing commencing time (after seating the restoration) : 5 min.

Tooth Preparation :

  • Prepare tooth in usual manner. For pulp capping, use calcium hydroxide paste Calcigel.
  • Clean the prepared teeth with pumice and water.
  • Rinse thoroughly with water. Remove excess moisture by blotting with a cotton pellet or gently blowing with an oil free air.

DO NOT DESICCATE. Prepared surfaces should appear moist (glistering).

Restoration Preparation :

  • Make sure that the restoration is pretreated and handled according to the manufacturer’s instructions.

Powder and Liquid Dispensing :

  • The standard powder to liquid ratio is 0.19/0.12 (1level scoop of powder to 2 drops of liquid.)
  • For accurate dispensing of powder lightly tap the bottle against the hand. Do not shake or invert.
  • Hold the liquid bottle vertically and squeeze gently.
  • Close bottle immediately after use.

MIXING : Dispense Powder and Liquid onto the pad. Using the plastic spatula, add all the powder to the liquid. Mix rapidly for 45-60 seconds.

NOTE : When mixing larger amounts, divide the powder into two equal parts. Mix the first portion with all of liquid for 15 seconds. Incorporate the remaining portion & mix the whole thoroughly for 45 seconds (Total 60 seconds).

APPLICATIONS : IMMEDIATELY apply (within 1 minute after dispensing) to the surfaces to be coated using a micro applicators, DO NOT AIR BLOW.

NOTE : Should the coated surfaces be contaminated with water, blood or saliva, wash and dry the surface and repeat the coating procedure.


  • Coat the internal surface of the restoration with sufficient cement and seat immediately. The working time is 2 minutes from start of mixing at 23±1°C (73.40±1°F). Higher temperature shorten working time.
  • Maintain Moderate pressure.
  • Start removing excess cement when it feels rubbery.
  • Finishing can be started 4 minutes 30 seconds after seating the restoration.


  • Crysta Luting should not be used if the patient is known to be allergic to any of the ingredient used.
  • Do not apply the material directly onto areas near the pulp or on to the exposed pulp as irritation may occur.


  • In case of contact with oral tissue or skin, remove immediately with a sponge or cotton soaked in alcohol. Flush with water. To avoid contact, a rubber dam and/or local butter can be used to isolate the operation field from the skin or oral tissue.
  • In case of contact with eyes flush immediately with water and seek medical attention.
  • DO NOT mix powder or liquid with component of other glass ionomer cements.
  • This product is not indicated for filling or core buildup.

Storage Conditions : Store at temperature between 10°C to 24°C. Close the cap carefully after use. Keep away from moisture. Shelf life not affected after opening if stored in a cool dry place.

Shelf Life : 3 Years from date of manufacturing


Quick Cart

Add a product in cart to see here!