Fusion Core DC Flo

  1. Home
  2. Composites
  3. Fusion Core DC Flo

Fusion Core DC Flo

Flowable, Dual Cure, Nano-tech Core Build-Up Composite
  • Dual cure, two component core build-up material
  • Comes in a convenient auto-mix delivery syringe
  • With its convenient flow it stacks easily without any slumping offering good placement
  • Dual cure formulation facilitates complete curing


  • 1 x 9g Automix syringe,
  • 10 x Intra-oral Tips,
  • 10 x Endo Tips,
  • 1 x Instruction Manual



CE 0123
The product is audited & approved as per European standards and laws, and has a valid CE Certifications
MDSAP quality management system satisfies the regulatory jurisdictions requirements of MDSAP Countries.
CDSCO Registered
Registered & Approved as per MDR 2017 Guidelines by Central Drugs Standard Control Organization


  • Core build-up, for vital as well as non-vital teeth
  • Luting of fibre-reinforced resin posts


  • Light curing for time saving application
  • Additional chemical curing for complete polymerisation
  • Low heat development even in bulk application
  • Flowable, non slumping formula for convenient placement
  • Low shrinkage properties
Technical Data Standard Applied
1. Working Time 60 Sec ISO 4049
2. Setting Time 3 – 4 Min
3. Flexural Strength 60 – 70 MPa
4. Film Thickness 50 mm


There are no reviews yet.

Be the first to review “Fusion Core DC Flo”

Your email address will not be published. Required fields are marked *

Instructions for use :

A. Cementation of Posts

– The post space must be prepared in accordance with the requirements of the respective root post.
– Bond the tooth using a Dual cure bonding agent (Fusion Bond Dc), self etch (5th generation bonding agent) or a etch and rinse (7th generation bonding agent) bonding agent.Use a paper tip to remove any excess bonding agent from the canal prior to the application of light( to prevent Canal blockage)
– Apply Fusion core Dc Flo to the prepared rootcanal space . When doing so keep the end of the tip constantly immersed in the material. Coat the post with Fusion core Dc Flo and lute it into the root canal space.
– Using a suitable lamp, apply light to the material for 20 seconds or Leave the material to harden for approx. 5:00 minutes. ( Chemical Cure )
B. For Core build-up
– Remove existing fillings and caries from the tooth selected for corebuild up
Isolate the tooth using a rubberdam.
– Bond the tooth using a self etch(5th generation bonding agent) or a etch and rinse (7th generation bonding agent) bonding agent
– Place a matrix around the prepared tooth and apply Fusion core Dc Flo directly into the cavity. Allow Fusion core Dc Flo to bond intraorally for approx. 5 minutes or expose to a suitable light curing unit for 20- 40 seconds based on the thickness of the composite layer

– If used, remove a matrix only once the material has hardened fully.
– Preparation should be modified as desired restoration form using standard preparation instruments The dispensed material shall not be placed back in container and the dose once applied and used shall not be reused.

Warnings :

  1. Contamination by saliva, blood or water should be avoided during these procedures. When using dental adhesives, contamination will compromise dentin bonding and may result in decreased longevity of the restoration.
  2. A rubber dam is recommended for all indications where contamination may be possible.

Precautions :

  1. Use of zinc oxide, eugenol containing materials must be avoided.
  2. If refrigerated, allow Fusion Core DC Flo, to reach room temperature before use.

Contraindications : Fusion Core DC Flo contains methacrylates, amines, peroxides and BHT. It should not be used in case of known hypersensitivity/allergies to any of these ingredients.

Storage Conditions : Store at temperature between 10°C (50°F) and 24°C (75°F). Close the cap carefully after use. Keep away from moisture. Shelf life not affected after opening if stored in a cool dry place.

Shelf Life : 2 years from the date of manufacturing.

Quick Cart

Add a product in cart to see here!